This high strength, low odour, water based acrylic adhesive is specifically designed for use with FIX-R EPDM membrane to timber deck surfaces.
Available in 2.5L (7 – 10m² coverage), 5L (14 – 20m² coverage) and 15L pails (42 – 60m² coverage).
A high strength, solvent based bonding adhesive, specifically designed and manufactured for flat roofing installations. Suitable for a range of surfaces e.g. timber, brickwork, metal, PVC and concrete.
Available in 1L (1.5 – 2 m² coverage), 2.5L (4 – 5m² coverage) and 5L (8 – 10m² coverage).
FIX-R EPDM Primer is a solvent based product designed for one step cleaning and priming of EPDM and other suitable surfaces prior to the application of FIX-R Pressure Sensitive (PS) accessories such as 76mm PS Seam Tape, 152mm PS Cover Strip, 228mm PS Uncured Flashing, PS Pipe Seals and PS Walkway Pads.
Available in 0.5L and 1L containers.
FIX-R PS Secure Tape is manufactured to precise width and thickness criteria with a clear poly backing for easier on site application. FIX-R PS Secure Tape offers over 30% greater peel and sheer strength when compared to market rivals. This tape is designed for use with FIX-R EPDM roofing systems to fuse the EPDM Membranes together resulting in long term seam strength.
Available in 30.5m long rolls.
FIX-R 152mm PS Cover Strip is used for stripping in metal edging, drip edges, gravel stops and fastening plates. This tape consists of a 1.02mm semi cured EPDM strip laminated to a 0.89mm fully cured synthetic rubber based pressure sensitive adhesive.
Available in 152mm by 30.5m long rolls. Can be used when seaming with 76mm PS Secure Tape is not possible.
FIX-R PS Uncured Flashing Tape is easily moulded and highly adaptable to irregular shapes and surfaces. This self-curing tape is ideal for flashing and waterproofing of roof details such as pipes, corners, outlets and other penetrations.
Available in 228mm wide by 15.25m long rolls.
The datasheet can be found here.
FIX-R PS Pipe Seals are cured, pre-moulded EPDM Flashings for round flat roof penetrations, with pre-applied secure tape to the base and a stainless steel clamping ring.
Available in two sizes – small 12.5 – 76mm and large 25 – 152mm in diameter.
In common with most single ply material, EPDM will over time try and shrink by up to 10% back to the centre. The base tie-in controls the membrane movement and stops the membrane pulling away where the membrane turns up through an angle change. The rest of the movement is accommodated by the FIX-R Membrane and its ability to elongate by over 300%.
FIX-R PS RUSS Strip (Reinforced Universal Secure Strip) is used to mechanically secure EPDM Membranes to the substrate. The strip has tape pre-applied along one edge and can be installed horizontally or vertically in conjunction with Seam Fastening Plates below the EPDM Membrane for additional membrane securement.
Used with FIX-R RUSS Strip to securely clamp the RUSS to the vertical or horizontal surface. Must be used in conjunction with the appropriate fasteners for the substrate.
The FIX-R Water Cut-Off Mastic is a compression termination. This one part self-wetting mastic is used in a variety of situations where a compression termination of the FIX-R EPDM Membrane is required.
The FIX-R Lap Sealant cures off to give a cured rubber consistency. This allows the mastic bead to expand and contract with the environment. It’s ideal for sealing wall chase details and using as a finishing bead to compression type joints.
FIX-R Pressure Sensitive Walkway Pads are designed to protect the membrane in those areas exposed to repetitive foot traffic.
FIX-R PS Walkway Pads must be installed at all traffic concentration points such as roof hatches, access doors, rooftop ladders, etc. regardless of traffic frequency. They must also be installed if regular maintenance (once a month or more) is necessary to service rooftop equipment.